Skip to main content

Companies and market participants (manufacturer, authorised representative, importer and distributor)

Information on responsibilitues related to wheel-marking.

Jump to content

    Company

    The company must ensure that equipment on board that falls within the scope of the Regulations on marine equipment is wheel-marked. The company must keep the declaration of conformity on board for the equipment fitted on the vessel.

    For guidance, see the guidance circular on requirements for declarations of conformity for marine equipment (only available in Norwegian).

    The Regulations on marine equipment contain provisions on exemptions from the requirement for wheel-marked equipment:

    • for technical innovations
    • for trial and evaluation of equipment
    • when replacing equipment in a port outside the EEA

    Manufacturer

    The manufacturer is responsible for ensuring that the marine equipment it produces and places on the market complies with the requirements set out in the Regulations on marine equipment. By affixing the wheel-mark, manufacturers assume responsibility for guaranteeing that the marine equipment to which the mark is affixed has been designed and manufactured in accordance with the technical specifications and standards applicable to each item of equipment.
     
    The manufacturer shall:

    • prepare the necessary technical documentation (see, for example, Module B, point 3 of the Regulations on marine equipment) and ensure that the applicable conformity-assessment procedures are carried out.
    • draw up an EU declaration of conformity and affix the wheel mark to equipment that meets the applicable requirements.
    • keep the technical documentation and declaration of conformity for at least ten years after the wheel mark has been affixed, and in any case not for a shorter perios than the expected lifetime of the equipment concerned.
    • ensure that, in the case of series production, procedures are in place to guarantee continued conformity.
    • ensure that their products bear a type, batch or serial number, or another identification element enabling the product to be identified, or – where this is not possible due to the size or nature of the product – that the necessary information appears on the packaging or in accompanying documentation, or both, as appropriate.
    • indicate their name, company name or registered trade mark and contact address on the product or – where this is not possible – on the packaging or accompanying documentation, or both, as appropriate. The address must indicate a single point at which the manufacturer can be contacted.
    • ensure tha the product is acoompanied by instructions and all information necessary for safe installation on board and safe use of the product, including any operational limitations, in language that can be easily understood by the users, as well as all other documentation required uner international instruments or testing standards.
    • in cases where they consider, or have reason to believe, that a product does not comply with the requirements, immediatelt take the necessary corrective actions.

    Technical documentation requirements

    The technical documentation shall make it possible to assess the conformity of the marine equipment with the applicable requirement of the international instruments referred to in Article 4, and shall include an adequate analysis and assessment of the risk(s).

    The technical documentation shall specify the applicable requirements and shall cover, as far as relevant for the assessment, the design, manufacture and operation of the marine equipment. The technical documentation shall contain, wherever applicable, at least the following elements:

    1. a general description of the marine equipment
    2. conceptual design and manufacturing drawings and schemes of components, sub assemblies, circuits, etc.
    3. descriptions and explanations necessary for the understanding of those drawings and schemes and of the operation of the marine equipment
    4. a list of the requirements and testing standards which are applicable to the marine equipment concerned in accordance with this Directive, together with a description of the solutions adopted to meet those requirements 
    5. results of design calculations made, examinations carried out, etc.
    6. test reports

    In cases where the manufacturer considers, or has reason to believe, that a product to which they have affixed a wheel-mark does not comply with the applicable requirements relating to design, construction, performance or testing standards, they shall immediately take the necessary corrective actions to bring the product into conformity, or, where appropriate, withdraw or recall it.

    If the product presents a risk, the manufacturer shall, in addition, immediately notify the competent national authorities in the Member States and provide detailed information, in particular regarding the non-compliance and any corrective actions taken.

    See our website with information on the notification requirement for hazardous products for which the Norwegian Maritime Authority is the supervisory authority. 

    Authorised representative

    Manufacturers located outside the EEA shall, by written mandate, appoint an authorised representative within the EEA. The mandate shall specify the name of the authorised representative and their contact address.

    A representative shall perform the tasks specified in the mandate from the manufacturer. On the basis of the mandate, the authorised representative shall at least be able to:

    • make the EU declaration of conformity and the technical documentation available to national market-surveillance authorities for at least ten years after the wheel-mark has been affixed, and in any case for no shorter period than the expected lifetime of the equipment concerned
    • provide the Norwegian Maritime Authority, upon a reasoned request, with all information and documentation necessary to demonstrate that the product complies with the applicable requirements
    • cooperate with the Norwegian Maritime Authority, upon request, with any action taken to eliminate risks associated with products covered by the representative's mandate

    The authorised representative is not permitted to prepare technical documentation. The mandate therefore cannot include the preparation of such documentation.

    Importer and distrubutor

    Importers placing marine equipment on the market in EU/EEA countries shall indicate their name, company name or registered trade mark and contact address on the product or – where this is not possible – on the packaging or accompanying documentation, or both, as appropriate.

    Importers and distributors (dealers or shipyards) shall, upon a reasoned request, provide all information and documentation necessary to demonstrate that the product complies with the applicable requirements.

    For a period of at least ten years after the wheel-mark has been affixed – or for the product's expected lifetime, if longer – market participants shall be able to present to the NMA:

    • all market participants who have supplied them with a product
    • all market participants to whom they have supplied a product

    An importer or distributor who places marine equipment on the market or installe such equipment on board in their own name or under their own trademark shall be considered a manufacturer and accordingly assumes the same responsibilities and obligations as the manufacturer.

    An importer or distributor who makes modifications to marine equipment that has already been placed on the market is also considered a manufacturer if the modifications may affect the product's compliance with the relevant requirements.

    Notified Body

    All equipment that is required to be wheel-marked must be assessed by a Notified Body. For serially manufactured equipment, this is normally carried out through a type‑examination (Module B). A Notified Body must also be involved in the production phase (for example, Module D). The table in the Implementing Regulation (Column 4: Conformity assessment modules) specifies which modules apply to the different equipment categories.
     
     
    Manufacturers are free to choose any Notified Body, irrespective of the manufacturer’s nationality or the national authority that has designated the body.
     
    Notified Bodies upload the certificates they issue to EMSA’s MarED database.